Cart  

No products

0,00 € Shipping
0,00 € Tax
0,00 € Total

Prices are tax included

Check out

List for Quote

No products added yet

FAQ

Do you need help? Go to see our FAQ section.

Specials

No specials at this time

Arduino NANO 33 BLE with headers

Arduino NANO 33 BLE with headers

The smallest Arduino board that comes with an embeded 9-axis inertial sensor. Ideal for wearable devices and scientific experiments that require short-distance wireless communication.



More details...

23,97 €

ABX00034

No products added yet

Secure payment
Secure payment

Overview:

The Arduino Nano 33 BLE is an evolution of the traditional Arduino Nano. This board improvements will allow you to make larger programs than with the Arduino Uno (the program memory is 32 times bigger), and with a lot more variables (the RAM is 128 times bigger). 

The Nano 33 BLE comes with a 9 axis inertial measurement unit (IMU) which means that it includes an accelerometer, a gyroscope, and a magnetometer with 3-axis resolution each. This makes the Nano 33 BLE the perfect choice for more advanced robotics experiments, exercise trackers, digital compasses, etc.

If you used Arduino Nano in your projects in the past, the Nano 33 BLE is a pin-equivalent substitute. Your code will still work, but remember, it operates at 3.3V. This means that you need to revise your original design in case it is not 3.3V compatible. 

Path: > Arduino NANO 33 BLE with headers

The Arduino Nano 33 BLE is based on the nRF52840 microcontroller.

  • Microcontroller: nRF52840 (datasheet)
  • Operating Voltage: 3.3V
  • Input Voltage (limit): 21V
  • DC Current per I/O Pin: 15 mA
  • Clock Speed: 64MHz
  • CPU Flash Memory: 1MB (nRF52840)
  • SRAM: 256KB (nRF52840)
  • EEPROM: none
  • Digital Input / Output Pins: 14
  • PWM Pins: all digital pins
  • UART: 1
  • SPI: 1
  • I2C: 1
  • Analog Input Pins: 8 (ADC 12 bit 200 ksamples)
  • Analog Output Pins: Only through PWM (no DAC)
  • External Interrupts: all digital pins
  • LED_BUILTIN: 13
  • USB: Native in the nRF52840 Processor
  • Length: 45 mm
  • Width: 18 mm
  • Weight: 5 gr (with headers)

Batteries, Pins and board LEDs

  • Batteries: the Nano 33 BLE has no battery connector, nor charger. You can connect any external battery of your liking as long as you respect the voltage limits of the board.
  • Vin: This pin can be used to power the board with a DC voltage source. If the power is fed through this pin, the USB power source is disconnected. This pin is an INPUT. Respect the voltage limits to assure the proper functionality of the board.
  • 5V: This pin outputs 5V from the board when powered from the USB connector or from the VIN pin of the board. Note: for it to work, you need to short the VBUS jumper on the back of the board.
  • 3.3V: This pin outputs 3.3V through the on-board voltage regulator. Note: for ultra-low-power functionality, you should cut the 3V3 jumper on the back of the board, and use an external battery at 3V3.
  • LED ON: This LED is connected to the 5V input from either USB or VIN.
  • I2C pins: As opposed to other Arduino Nano boards, pins A4 and A5 have an internal pull-up and default to be used as an I2C Bus so usage as analog inputs is not recommended.
  • NFC: There is the possibility of attaching an external NFC antenna between pins D7 and D8 to activate Bluetooth® pairing of the board over NFC.

30 other products in the same category :