Cart  

No products

0,00 € Shipping
0,00 € Tax
0,00 € Total

Prices are tax included

Check out

List for Quote

No products added yet

FAQ

Do you need help? Go to see our FAQ section.

Specials

No specials at this time

Arduino MKR WiFi 1010 (WiFi & Bluetooth)

Arduino MKR WiFi 1010 (WiFi & Bluetooth)

The Arduino MKR WiFi 1010 is the simplest board for IoT projects with WiFi and Bluetooth connectivity.

More details...

34,36 €

ABX00023

No products added yet

Secure payment
Secure payment

Overview

Whether you are looking at building a sensor network connected to your office or home router, or if you want to create a BLE device sending data to a cellphone, the MKR WiFi 1010 is your one-stop-solution for many of the basic IoT application scenarios.

The board's main processor is a low power Arm® Cortex®-M0 32-bit SAMD21 (datasheet), like in the other boards within the Arduino MKR family. The WiFi and Bluetooth® connectivity is performed with a module from u-blox, the NINA-W10 (datasheet), a low power chipset operating in the 2.4GHz range. On top of those, secure communication is ensured through the Microchip® ECC508 crypto chip (datasheet). Besides that, you can find a battery charger, and a directionable RGB LED on-board.

Warning: Unlike most Arduino boards, the MKR WIFI 1010 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

Path: > Arduino MKR WiFi 1010 (WiFi & Bluetooth)

Technical Specifications

The Arduino MKR WAN 1010 is based on the SAMD21 microcontroller.


Microcontroller SAMD21 Cortex®-M0+ 32bit low power ARM MCU (datasheet)
Radio module u-blox NINA-W102 (datasheet)
Board Power Supply (USB/VIN) 5V
Secure Element ATECC508 (datasheet)
Supported Battery Li-Po Single Cell, 3.7V, 700mAh Minimum
Circuit Operating Voltage 3.3V
Digital I/O Pins 8
PWM Pins 13 (0 .. 8, 10, 12, 18 / A3, 19 / A4)
UART 1
SPI 1
I2C 1
Analog Input Pins 7 (ADC 8/10/12 bit)
Analog Output Pins 1 (DAC 10 bit)
External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, 16 / A1, 17 / A2)
DC Current per I/O Pin 7 mA
CPU Flash Memory 256 KB (internal)
SRAM 32 KB
EEPROM no
Clock Speed 32.768 kHz (RTC), 48 MHz
LED_BUILTIN 6
USB Full-Speed USB Device and embedded Host
LED_BUILTIN 6
Length 61.5 mm
Width 25 mm
Weight 32 gr.

Batteries, Pins and board LEDs

  • Battery capacity: Rechargeable Li-Ion, or Li-Po. Please make sure the battery connector suits your battery.
  • Battery connector: The connector is of type JST S2B-PH-SM4-TB(LF)(SN). The mating connector is JST PHR-2.
  • Vin: This pin can be used to power the board with a regulated 5V source. If the power is fed through this pin, the USB power source is disconnected. This is the only way you can supply 5v (range is 5V to maximum 6V) to the board not using USB. This pin is an INPUT.
  • 5V: This pin outputs 5V from the board when powered from the USB connector or from the VIN pin of the board. It is unregulated and the voltage is taken directly from the inputs.
  • VCC: This pin outputs 3.3V through the on-board voltage regulator. This voltage is 3.3V if USB or VIN is used and equal to the series of the two batteries when they are used
  • LED ON: This LED is connected to the 5V input from either USB or VIN. It is not connected to the battery power, thus minimizing the impact on battery usage. It is therefore normal to have the board properly running on battery power without the LED ON being lit.
  • Onboard LED: On MKR WAN 1010 the onboard LED is connected to D6.

30 other products in the same category :